- Posts: 116
- Thank you received: 5
Cubo Kick 15
- anjmoor
- Offline
- Premium Member
Please Log in or Create an account to join the conversation.
- SuperDon
- Offline
- Senior Member
- Posts: 69
- Thank you received: 0
Cubo15 wrote:
Always good, to hear good reviews, glad you like it.Well, results were very good
That's a good in-between-driver. It will work in both Cubo 15 and Cubo Kick.I have already a couple of 18sound 15w700
As Cubo Kick is about 40% reflex and 60% horn, some drivers will find a better loading by the reflex part and some will find better loading by the horn part of it. The 15W700 matches both parts about equally well.
Best regards
Cubo
Is there any other drivers that will match the above mentioned drivers performance but with a little more power?
Please Log in or Create an account to join the conversation.
- Cubo15
- Topic Author
- Offline
- Platinum Member
- Posts: 916
- Thank you received: 131
I haven't had a single problem with t-nuts (of any kind) anymore since my 3-step-program:The only issue I can see is if a t-nut rounds off
- Glue-ing the t-nuts in place
- Using slightly longer bolts to secure the driver
- Use a long greased bolt with large washers to pull the t-nut in
I'm using a thick glue that is applied on the entire contact surface area between wood and t-nut. Using a longer bolt to secure the driver so that the entire threat of the t-nut is loaded before any significant strain is put on it. I'm using richly applied ball-bearing grease on a bolt (solely used for that purpose and replaced in time) to pull the t-nut in, again the whole thread of the t-nut is used before any strain is put on it.
Sometimes when glue-ing the t-nut, especially when using mdf, you can feel the t-nut springing back up (1 mm or so) when the strain on the bolt, too pull the t-nut in, is released. In that case I let the glue dry with the bolt tightened, to ensure maximum bond strength.
Usable up to at least 190 Hz, also usable in Cubo 15, would be a good choice for 12V systems, considering the very low weight.how would the B&C 15CL76 preform in these kick?
Yes, output will be higher below 130 Hz, in exchange for slightly less output above 130 Hz.I'm curious to hear how a pd1550 would sound in these. Is it on the more on the low end emphasis?
That's hard to say when testing only one driver However wadding will help prevent sound from the rear of the driver to exit through the ports, you could even close all ports and see how that works out for ya.I am going to put a little wadding in the chamber as there are some resonances when pushed hard I would say this is the cab not the driver.
Generally speaking, drivers with the highest power handling that can be used in both Cubo 15 and Cubo Kick, will have: A 4" voice coil, a Mms between 80 - 120 gram, a n0 around 3% (usually because the Fs is in the mid to high forties), a gap height of 12 mm or less, a voice coil winding depth of 23 mm or less. Le around 1.75 or preferably less.Is there any other drivers that will match the above mentioned drivers performance but with a little more power?
The PD.1550 mentioned above is good one and from 18Sound, the 15NLW9300 (neo) and the 15MB1000 (ferrite).
Best regards
Cubo
Please Log in or Create an account to join the conversation.
- anjmoor
- Offline
- Premium Member
- Posts: 116
- Thank you received: 5
Please Log in or Create an account to join the conversation.
- pirata
- Offline
- New Member
- Posts: 15
- Thank you received: 3
Please Log in or Create an account to join the conversation.
- Ganon
- Offline
- New Member
- Posts: 4
- Thank you received: 0
We have the box and a Eminence kappa pro 15lf driver, so i hope it is suitable.
My friend who build it was pleased to build it and said it was nice and easy, really good build!
Looking forward to listen to it!
Thanks!
Please Log in or Create an account to join the conversation.
- Cubo15
- Topic Author
- Offline
- Platinum Member
- Posts: 916
- Thank you received: 131
Best regards
Cubo
Please Log in or Create an account to join the conversation.
- Foca_Dacian
- Offline
- New Member
- Posts: 3
- Thank you received: 0
I am building 2 cubo 18 ext(gave up on more compact(20 liters less than Cubo) reflex boxes that I was planning to build ,do to lack of sufficient output/cabinet size for the reflex subs imh,also I had F3@46 hz with the reflex,as to the 40 hz that cubo's can give)
In the future I will build two more cubo 18 ext+2 cubo kick 15 so that I'll have 2 cubo ext+cubo kick 15/side, 10 inch mid horns+1.4 inch comps)
The drivers I use in the Cubo's are FaitalPro18FH510,at the moment with 12 inch tops loaded with 12PR310 and HF144 from faital pro also.
What driver from Faital Pro (looks like I'm a Faital Pro fan,or i can get them at good prices,don't know which one it is)do you recommend for the Cubo Kick 15,so that it keeps up with 2 cubo 18 ext/side loaded with my drivers.How does the 15FH510 sound like?(almost identical to 15FH500 which is recomended)
Have a great day,
Dacian Foca
Please Log in or Create an account to join the conversation.
- Cubo15
- Topic Author
- Offline
- Platinum Member
- Posts: 916
- Thank you received: 131
Best regards
Cubo
Please Log in or Create an account to join the conversation.
- anjmoor
- Offline
- Premium Member
- Posts: 116
- Thank you received: 5
I only lugged half the system to the yard.
Cubo 15 extended loaded with eminence delta 15 lf 4 ohm run off a w-audio da 1300.
Cubo kick 12 loaded with P Audio ES200s run off the other side of the da 1300.
Mid tops are the fane design loaded with the guts out of my old mid tops, port tubes not installed yet run off an Inter-m 500.
Crossover settings
Sub 40-110 hz
Cubo kick 110-240 he
Mid tops everything else above.
Videos here
More test videos on my YouTube channel
Please Log in or Create an account to join the conversation.