heart MN-246

14 years 4 months ago - 10 years 1 week ago #6817 by giveortake
MN-246 was created by giveortake
Use this thread to discuss the MN-246 design posted here

What is your philosophy of life or your creed ?
\"Have a good time, ALL THE TIME\"

Wisdom is better than silver and gold !

Please Log in or Create an account to join the conversation.

14 years 1 month ago #7879 by gtrmech
Replied by gtrmech on topic MN-246
How would this design work with the Eminence Sigma Pro 18-A2 8ohm driver. Its also hard to tell from the drawing exactly how the driver opening is put together. Is it completely open and the 2 small braces go across the opening, or is the opening only between the braces??

Please Log in or Create an account to join the conversation.

14 years 1 month ago #7935 by giveortake
Replied by giveortake on topic MN-246

gtrmech wrote: How would this design work with the Eminence Sigma Pro 18-A2 8ohm driver. Its also hard to tell from the drawing exactly how the driver opening is put together. Is it completely open and the 2 small braces go across the opening, or is the opening only between the braces??


From the designer:

"The Sigma appears a bit limited to me: Its specs while not too bad are not optimal, its Xmax of 6.1mm is not enough and is going to limit output.
Therefore I do not recommend this driver for the MN-246."

What is your philosophy of life or your creed ?
\"Have a good time, ALL THE TIME\"

Wisdom is better than silver and gold !

Please Log in or Create an account to join the conversation.

14 years 1 week ago #8224 by gtrmech
Replied by gtrmech on topic MN-246
Ok.. Would the Eminence Kilomax be a better choice? *Power handling: 1,250 watts RMS/2,500 watts max *VCdia: 4" *Le: 2.38 mH *Impedance: 8 ohms *Re: 5.84 ohms *Frequency range: 33-600 Hz *Magnet weight: 109 oz. *Fs: 33 Hz *SPL: 95.5 dB 1W/1m *Vas: 8.5 cu. ft. *Qms: 14.24 *Qes: 0.58 *Qts: 0.56 *Xmax: 9.8 mm *Dimensions: Overall Diameter: 18", Cutout Diameter: 16.56", Mounting Depth: 8.15".The XMAX spec seems to be more like the RCF driver.

Please Log in or Create an account to join the conversation.

14 years 1 week ago #8228 by MAutopsy
Replied by MAutopsy on topic MN-246
In the couple years i have been putting cabs together and experimenting i have found that you cannot stray from the driver that a bandpass or bandpass horn box is designed for.

Please Log in or Create an account to join the conversation.

14 years 1 week ago #8237 by bee
Replied by bee on topic MN-246
+1 save up and get the correct driver.....

Please Log in or Create an account to join the conversation.

13 years 9 months ago #8909 by guest
Replied by guest on topic MN-246
Is it possible to cut this sub in two parts? it will be after 60.8cmThx

Please Log in or Create an account to join the conversation.

13 years 7 months ago #9127 by guest
Replied by guest on topic MN-246
What abou RCF L18P300 in this design? Would it be ok?

Please Log in or Create an account to join the conversation.

13 years 6 months ago #9284 by vaze82
Replied by vaze82 on topic MN-246
hi, i like the design. just wanted to know if the Precision Devices 1850 driver would work on the cabinet n if it would any idea how would it sound.

Please Log in or Create an account to join the conversation.

13 years 6 months ago #9316 by vaze82
Replied by vaze82 on topic MN-246
hi, i like the USB sub design. just wanted to know if the Precision Devices 1850 driver would work on the cabinet n if it would any idea how would it sound.

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum