heart MN-246

13 years 6 months ago - 9 years 2 months ago #6817 by giveortake
MN-246 was created by giveortake
Use this thread to discuss the MN-246 design posted here

What is your philosophy of life or your creed ?
\"Have a good time, ALL THE TIME\"

Wisdom is better than silver and gold !

Please Log in or Create an account to join the conversation.

13 years 3 months ago #7879 by gtrmech
Replied by gtrmech on topic MN-246
How would this design work with the Eminence Sigma Pro 18-A2 8ohm driver. Its also hard to tell from the drawing exactly how the driver opening is put together. Is it completely open and the 2 small braces go across the opening, or is the opening only between the braces??

Please Log in or Create an account to join the conversation.

13 years 3 months ago #7935 by giveortake
Replied by giveortake on topic MN-246

gtrmech wrote: How would this design work with the Eminence Sigma Pro 18-A2 8ohm driver. Its also hard to tell from the drawing exactly how the driver opening is put together. Is it completely open and the 2 small braces go across the opening, or is the opening only between the braces??


From the designer:

"The Sigma appears a bit limited to me: Its specs while not too bad are not optimal, its Xmax of 6.1mm is not enough and is going to limit output.
Therefore I do not recommend this driver for the MN-246."

What is your philosophy of life or your creed ?
\"Have a good time, ALL THE TIME\"

Wisdom is better than silver and gold !

Please Log in or Create an account to join the conversation.

13 years 2 months ago #8224 by gtrmech
Replied by gtrmech on topic MN-246
Ok.. Would the Eminence Kilomax be a better choice? *Power handling: 1,250 watts RMS/2,500 watts max *VCdia: 4" *Le: 2.38 mH *Impedance: 8 ohms *Re: 5.84 ohms *Frequency range: 33-600 Hz *Magnet weight: 109 oz. *Fs: 33 Hz *SPL: 95.5 dB 1W/1m *Vas: 8.5 cu. ft. *Qms: 14.24 *Qes: 0.58 *Qts: 0.56 *Xmax: 9.8 mm *Dimensions: Overall Diameter: 18", Cutout Diameter: 16.56", Mounting Depth: 8.15".The XMAX spec seems to be more like the RCF driver.

Please Log in or Create an account to join the conversation.

13 years 2 months ago #8228 by MAutopsy
Replied by MAutopsy on topic MN-246
In the couple years i have been putting cabs together and experimenting i have found that you cannot stray from the driver that a bandpass or bandpass horn box is designed for.

Please Log in or Create an account to join the conversation.

13 years 2 months ago #8237 by bee
Replied by bee on topic MN-246
+1 save up and get the correct driver.....

Please Log in or Create an account to join the conversation.

12 years 11 months ago #8909 by guest
Replied by guest on topic MN-246
Is it possible to cut this sub in two parts? it will be after 60.8cmThx

Please Log in or Create an account to join the conversation.

12 years 10 months ago #9127 by guest
Replied by guest on topic MN-246
What abou RCF L18P300 in this design? Would it be ok?

Please Log in or Create an account to join the conversation.

12 years 9 months ago #9284 by vaze82
Replied by vaze82 on topic MN-246
hi, i like the design. just wanted to know if the Precision Devices 1850 driver would work on the cabinet n if it would any idea how would it sound.

Please Log in or Create an account to join the conversation.

12 years 8 months ago #9316 by vaze82
Replied by vaze82 on topic MN-246
hi, i like the USB sub design. just wanted to know if the Precision Devices 1850 driver would work on the cabinet n if it would any idea how would it sound.

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum